Wiper and washer

In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster.

In freezing weather, do not use the windshield washer until the windshield is sufficiently warmed by the defroster.

Otherwise the washer fluid can freeze on the windshield, blocking your view.

 Do not operate the washer continuously for more than 10 seconds, or when the washer fluid tank is empty. This may cause overheating of the washer motor.

Do not operate the washer continuously for more than 10 seconds, or when the washer fluid tank is empty. This may cause overheating of the washer motor.

Check the washer fluid level frequently, such as at fuel stops.

Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the windshield washer.

In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers.

Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper motor to burn out. If the wiper blades are frozen to the window glass, be sure to operate the defroster, windshield wiper deicer (if equipped) or rear window defogger before turning on the wiper.

If the wipers stop during operation because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the LOCK position and clean the window glass to allow proper wiper operation.

Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent.

Refer to Windshield washer fluid F11-38.

Also, when driving the vehicle when there are freezing temperatures, use non-freezing type wiper blades.

Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzine. This will cause deterioration of the wiper blades.

NOTE
The wiper operates only when the ignition switch is in the ON or Acc position.

The front wiper motor is protected against overloads by a circuit breaker.

If the motor operates continuously under an unusually heavy load, the circuit breaker may trip to stop the motor temporarily. If this happens, park your vehicle in a safe place, turn off the wiper switch, and wait for approximately 10 minutes. The circuit breaker will reset itself, and the wipers will again operate normally.

Clean your wiper blades and window glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window.

Grease, wax, insects or other material on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer surface of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water.

If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. For replacement instructions, refer to Replacement of wiper blades.

See also:

3.6-liter H6 Engine: Premium Performance with Regular-Grade Fuel
The new 3.6-liter H6 engine replaces the previous 3.0-liter H6, yet features the same external dimensions thanks primarily to a unique shortened connecting rod design. As a result, this larger-dis ...

Example of accident in which the drivers/drivers and front passengers SRS frontal airbag(s) will most likely deploy.
A head-on collision against a thick concrete wall at a vehicle speed of 12 to 19 mph (20 to 30 km/h) or higher activates only the drivers SRS frontal airbag or both drivers and front passe ...

Maximum allowable speeds
The following table shows the maximum speeds that are possible with each different gear. The tachometers needle will enter the red area if these speeds are exceeded. With the exception of cases wher ...